Glossary NEW

Total pressure measured from zero.

See Temperature, Absolute.

The chemical process by which a hygroscopic desiccant, having a high affinity with water, melts and becomes a liquid by absorbing the condensed moisture.

Quantity of gas actually compressed and delivered to the discharge system at rated speed and under rated conditions. Also called Free Air Delivered (FAD).

See Compression, Adiabatic.

The process by which a desiccant with a highly porous surface attracts and removes the moisture from compressed air. The desiccant is capable of being regenerated.

A heat exchanger used for cooling air discharged from a compressor. Resulting condensate may be removed by a moisture separator following the aftercooler.

See Gas Bearings.

See Receiver.

The measured ambient pressure for a specific location and altitude.

A device which operates compressors in sequence according to a programmed schedule.

See Horsepower, Brake.

The amount of air flow delivered under specific conditions, usually expressed in cubic feet per minute (cfm).

A gauge that measures air flow as a percentage of capacity, used in rotary screw compressors

The actual volume flow rate of air or gas compressed and delivered from a compressor running at its rated operating conditions of speed, pressures, and temperatures. Actual capacity is generally expressed in actual cubic feet per minute (acfm) at conditions prevailing at the compressor inlet.

A valve which permits flow in only one direction.

The maximum cylinder volume on the working side of the piston minus the displacement volume per stroke. Normally it is expressed as a percentage of the displacement volume.

An auxiliary volume that may be opened to the clearance space, to increase the clearance, usually temporarily, to reduce the volumetric efficiency of a reciprocating compressor.

A factor expressing the deviation of a gas from the laws of thermodynamics. (See also Supercompressibility)

The ratio of the absolute discharge pressure to the absolute inlet pressure.

Compression in which no heat is transferred to or from the gas during the compression process.

Compression is which the temperature of the gas remains constant.

Compression in which the relationship between the pressure and the volume is expressed by the equation PVn is a constant.

A system in which the compressor is run continuously and matches air supply to air demand by varying compressor load.

The limiting value of saturation pressure as the saturation temperature approaches the critical temperature.

The highest temperature at which well-defined liquid and vapor states exist. Sometimes it is defined as the highest temperature at which it is possible to liquify a gas by pressure alone.

Volumetric air flow rate.

Flow rate of air at a certain point at a certain condition at that point.

cfm of air delivered to a certain point at a certain condition, converted back to ambient conditions.

Cfm flowing through the compressor inlet filter or inlet valve under rated conditions.

Flow of free air measured and converted to a standard set of reference conditions (14.5 psia, 68°F, and 0% relative humidity).

Respectively, the minimum and maximum discharge pressures at which the compressor will switch from unload to load operation (cut in) or from load to unload (cut out).

The series of steps that a compressor with unloading performs; 1) fully loaded, 2) modulating (for compressors with modulating control), 3) unloaded, 4) idle.

Amount of time for a compressor to complete one cycle.

The difference in air or gas temperature between the outlet of the intercooler and the inlet of the compressor.

Melting and becoming a liquid by absorbing moisture.

Flow of air at specific conditions required at a point or by the overall facility.

A material having a large proportion of surface pores, capable of attracting and removing water vapor from the air.

The temperature at which moisture in the air will begin to condense if the air is cooled at constant pressure. At this point the relative humidity is 100%

A stationary element between the stages of a multi-stage centrifugal compressor. It may include guide vanes for directing the flowing medium to the impeller of the succeeding stage. In conjunction with an adjacent diaphragm, it forms the diffuser surrounding the impeller.

A method of removing heat from the flowing medium by circulation of a coolant in passages built into the diaphragm.

A stationary passage surrounding an impeller, in which velocity pressure imparted to the flowing medium by the impeller is converted into static pressure.

See Logic Controls.

Air pressure produced at a particular point in the system under specific conditions.

The temperature at the discharge flange of the compressor.

The volume swept out by the piston or rotor(s) per unit of time, normally expressed in cubic feet per minute.

The drop in pressure at the outlet of a pressure regulator, when a demand for air occurs.

Compressors in which air or gas is compressed by the mechanical action of rotating impellers imparting velocity and pressure to a continuously flowing medium. (Can be centrifugal or axial design).

Any reference to efficiency must be accompanied by a qualifying statement which identifies the efficiency under consideration, as in the following definitions of efficiency:

Ratio of theoretical power to power actually imparted to the air or gas delivered by the compressor.

Ratio of the theoretical work (as calculated on a isothermal basis) to the actual work transferred to a gas during compression.

Ratio of power imparted to the air or gas to brake horsepower (bhp).

Ratio of the polytropic compression energy transferred to the gas, to the actual energy transferred to the gas.

Ratio of actual capacity to piston displacement.

A term sometimes applied to a compressor in which the inlet pressure is less than atmospheric pressure.

Turbines or engines in which a gas expands, doing work, and undergoing a drop in temperature. Use of the term usually implies that the drop in temperature is the principle objective. The orifice in a refrigeration system also performs this function, but the expander performs it more nearly isentropically, and thus is more effective in cryogenic systems.

Devices for separating and removing particulate matter, moisture or entrained lubricant from air.

The means of connecting a compressor inlet or discharge connection to piping by means of bolted rims (flanges).

The general subject of instruments and controls dependent upon low rate of flow of air or gas at low pressure as the operating medium. These usually have no moving parts.

Air at atmospheric conditions at any specified location, unaffected by the compressor.

Air compressor operation at full speed with a fully open inlet and discharge delivering maximum air flow.

One of the three basic phases of matter. While air is a gas, in pneumatics the term gas normally is applied to gases other than air.

Load carrying machine elements permitting some degree of motion in which the lubricant is air or some other gas.

The pressure determined by most instruments and gauges, usually expressed in psig. Barometric pressure must be considered to obtain true or absolute pressure.

stationary element that may be adjustable and which directs the flowing medium approaching the inlet of an impeller.

The energy, in foot pounds, required to compress adiabatically to deliver one pound of a given gas from one pressure level to another.

The energy, in foot pounds, required to compress polytropically to deliver one pound of a given gas from one pressure level to another.

Horsepower delivered to the output shaft of a motor or engine, or the horsepower required at the compressor shaft to perform work.

The horsepower calculated from compressor indicator diagrams. The term applies only to displacement type compressors.

The horsepower required to isothermally compress the air or gas delivered by the compressor at specified conditions.

The relative humidity of a gas (or air) vapor mixture is the ratio of the partial pressure of the vapor to the vapor saturation pressure at the dry bulb temperature of the mixture.

The weight of water vapor in an air vapor mixture per pound of dry air.

The time lag in responding to a demand for air from a pressure regulator.

The part of the rotating element of a dynamic compressor which imparts energy to the flowing medium by means of centrifugal force. It consists of a number of blades which rotate with the shaft.

Power as calculated from compressor-indicator diagrams.

A pressure – volume diagram for a compressor or engine cylinder, produced by direct measurement by a device called an indicator.

A curved inlet section of an impeller.

The actual pressure at the inlet flange of the compressor.

The removal of heat from air or gas between compressor stages.

The difference in air or gas temperatures between the inlet of the compressor and the outlet of the intercooler.

When the temperature of the air or gas leaving the intercooler is equal to the temperature of the air or gas entering the inlet of the compressor.

See Compression, Isentropic.

See Compression, Isothermal.

An unintended loss of compressed air to ambient conditions.

A compressor in which a vaned rotor revolves in an elliptical stator, with the spaces between the rotor and stator sealed by a ring of liquid rotating with the impeller.

Ratio of average compressor load to the maximum rated compressor load over a given period of time.

Time period from when a compressor loads until it unloads.

Control method that allows the compressor to run at full-load or at no load while the driver remains at a constant speed.

System which adapts to varying demand by throttling the compressor inlet proportionally to the demand.

Two or more compressors, each with a separate casing, driven by a single driver, forming a single unit.

A dynamic compressor having two or more rows of rotating elements operating in series on a single rotor and in a single casing.

A dynamic compressor having two or more impellers operating in series in a single casing.

Compressors having two or more stages operating in series.

The condition when the temperature of air leaving the intercooler equals the of air at the compressor intake.

Usually a plot of discharge pressure versus inlet capacity and shaft horsepower versus inlet capacity.

The volume swept by the piston; for multistage compressors, the piston displacement of the first stage is the overall piston displacement of the entire unit.

Tools that operate by air pressure.

See Compression, Polytropic.

See Head, Polytropic.

Compressors in which successive volumes of air or gas are confined within a closed space and the space mechanically reduced, resulting in compression. These may be reciprocating or rotating.

The mechanical power required to compress polytropically and to deliver, through the specified range of pressures, the gas delivered by the compressor.

Force per unit area, measured in pounds per square inch (psi).

For a given pressure, the temperature at which water will begin to condense out of air.

Loss of pressure in a compressed air system or component due to friction or restriction.

Difference between minimum and maximum pressures for an air compressor. Also called cut in-cut out or load-no load pressure range.

See Compression Ratio.

The difference between discharge pressure and intake pressure.

The total pressure measured from absolute zero (i.e. from an absolute vacuum).

See Critical Pressure.

The pressure at the discharge connection of a compressor. (In the case of compressor packages, this should be at the discharge connection of the package

The absolute total pressure at the inlet connection of a compressor.

The total pressure minus the static pressure in an air or gas stream.

Volume rate of air flow at rated pressure at a specific point.

The operating pressure at which compressor performance is measured.

Receiver? A vessel or tank used for storage of gas under pressure. In a large compressed air system there may be primary and secondary receivers.

Compressor in which the compressing element is a piston having a reciprocating motion in a cylinder.

The ratio of the partial pressure of a vapor to the vapor saturation pressure at the dry bulb temperature of a mixture.

Cubic feet per minute (cfm) of air required at the inlet to the distribution system.

A dimensionless flow parameter (h < D/:), in which h is a significant dimension, often a diameter, < is the fluid velocity, D is the mass density, and : is the dynamic viscosity, all in consistent units.

The rotating element of a compressor. In a dynamic compressor, it is composed of the impeller(s) and shaft, and may include shaft sleeves and a thrust balancing device.

Devices used to separate and minimize leakage between areas of unequal pressure.

The order in which compressors are brought online.

The part by which energy is transmitted from the prime mover through the elements mounted on it, to the air or gas being compressed.

A pad, usually metallic and embedded in concrete, on which the compressor and driver are mounted.

The ratio of the specific weight of air or gas to that of dry air at the same pressure and temperature.

The weight of water vapor in an air-vapor mixture per pound of dry air.

A measure of air compressor efficiency, usually in the form of bhp/100 acfm.

Weight of air or gas per unit volume.

The speed of a compressor refers to the number of revolutions per minute (rpm) of the compressor drive shaft or rotor shaft.

A series of steps in the compression of air or a gas.

The Compressed Air & Gas Institute and PNEUROP have adopted the definition used in ISO standards. This is air at 14.5 psia (1 bar); 68 F (20 C) and dry (0% relative humidity).

A system in which air supply is matched to demand by the starting and stopping of the unit.

See Compressibility

A phenomenon in centrifugal compressors where a reduced flow rate results in a flow reversal and unstable operation.

The capacity in a dynamic compressor below which operation becomes unstable.

The ratio of the computed isentropic temperature rise to the measured total temperature rise during compression. For a perfect gas, this is equal to the ratio of the isentropic enthalpy rise to the actual enthalpy rise.

The temperature of air or gas measured from absolute zero. It is the Fahrenheit temperature plus 459.6 and is known as the Rankine temperature. In the metric system, the absolute temperature is the Centigrade temperature plus 273 and is known as the Kelvin temperature.

See Critical Temperature.

The total temperature at the discharge connection of the compressor.

The total temperature at the inlet connection of the compressor.

The actual temperature of a moving gas stream. It is the temperature indicated by a thermometer moving in the stream and at the same velocity.

The temperature which would be measured at the stagnation point if a gas stream were stopped, with adiabatic compression from the flow condition to the stagnation pressure.

The power required to compress a gas isothermally through a specified range of pressures.

A torsional moment or couple. This term typically refers to the driving couple of a machine or motor.

The total electrical power input to a compressor, including drive motor, belt losses, cooling fan motors, VSD or other controls, etc.

Compressors of 30 bhp or less, generally combined with all components required for operation.

(No load) Compressor operation in which no air is delivered due to the intake being closed or modified not to allow inlet air to be trapped.

Compressors which operate with an intake pressure below atmospheric pressure and which discharge to atmospheric pressure or slightly higher.

Devices with passages for directing flow into alternate paths or to prevent flow.

A stationary, spiral shaped passage which converts velocity head to pressure in a flowing stream of air or gas.

Compressors cooled by water circulated through jackets surrounding cylinders or casings and/or heat exchangers between and after stages.